Lincoln Navigator: Climate Control System
- Climate Control System - General Information
- Specifications
- Climate Control System - Component Location. Description and Operation
- Climate Control System - System Operation and Component Description. Description and Operation
- Climate Control System. Diagnosis and Testing
- Air Conditioning (A/C) Clutch Air Gap Adjustment. General Procedures
- Air Conditioning (A/C) Compressor Leak Detection. General Procedures
- Air Conditioning (A/C) Odor Treatment. General Procedures
- Air Conditioning (A/C) System Flushing. General Procedures
- Air Conditioning (A/C) System Leak Test Using Forming Gas. General Procedures
- Air Conditioning (A/C) System Recovery, Evacuation and Charging. General Procedures
- Climate Control Tools and Equipment. General Procedures
- Condenser Core Leak Check. General Procedures
- Electronic Leak Detection. General Procedures
- Evaporator Core Leak Check. General Procedures
- Fluorescent Dye Leak Detection. General Procedures
- Heater Core Leak Check. General Procedures
- Refrigerant Identification Testing. General Procedures
- Refrigerant Oil Adding. General Procedures
- Refrigerant System Tests - 3.5L EcoBoost (272kW/370PS). General Procedures
- Reset the Outside Air Temperature Sensor Learned Values. General Procedures
- Air Conditioning (A/C) Clutch and Air Conditioning (A/C) Clutch Field Coil. Removal and Installation
- Air Conditioning (A/C) Compressor. Removal and Installation
- Air Conditioning (A/C) Compressor Inlet Line. Removal and Installation
- Air Conditioning (A/C) Compressor Outlet Line. Removal and Installation
- Air Conditioning (A/C) Pressure Transducer. Removal and Installation
- Air Distribution Door Actuator. Removal and Installation
- Air Inlet Door Actuator. Removal and Installation
- Ambient Air Temperature Sensor. Removal and Installation
- Blower Motor Control Module. Removal and Installation
- Cabin Air Filter. Removal and Installation
- Cabin Heater Coolant Pump. Removal and Installation
- Center Registers. Removal and Installation
- Climate Control Housing. Removal and Installation
- Condenser. Removal and Installation
- Desiccant Bag. Removal and Installation
- Driver Side Footwell Air Discharge Temperature Sensor. Removal and Installation
- Driver Side Register. Removal and Installation
- Driver Side Register Air Discharge Temperature Sensor. Removal and Installation
- Evaporator. Removal and Installation
- Evaporator Temperature Sensor. Removal and Installation
- Heater Core. Removal and Installation
- Heating, Ventilation and Air Conditioning (HVAC) Control Module. Removal and Installation
- In-Vehicle Temperature and Humidity Sensor. Removal and Installation
- Passenger Side Footwell Air Discharge Temperature Sensor. Removal and Installation
- Passenger Side Register. Removal and Installation
- Passenger Side Register Air Discharge Temperature Sensor. Removal and Installation
- Passenger Side Temperature Door Actuator. Removal and Installation
- Sunload Sensor. Removal and Installation
- Temperature Door Actuator. Removal and Installation
- Thermostatic Expansion Valve. Removal and Installation
- Thermostatic Expansion Valve Manifold and Tube Assembly. Removal and Installation
- Climate Control Housing. Disassembly and Assembly
- Rear Climate Control
- Rear Climate Control - Component Location. Description and Operation
- Rear Climate Control - System Operation and Component Description. Description and Operation
- Rear Air Discharge Temperature Sensor. Removal and Installation
- Rear Air Distribution Door Actuator. Removal and Installation
- Rear Blower Motor. Removal and Installation
- Rear Blower Motor Speed Control. Removal and Installation
- Rear Climate Control Housing. Removal and Installation
- Rear Evaporator. Removal and Installation
- Rear Evaporator Rear Outlet and Inlet Line. Removal and Installation
- Rear Footwell Air Discharge Temperature Sensor. Removal and Installation
- Rear Heater Core. Removal and Installation
- Rear Heater Core Inlet Line. Removal and Installation
- Rear Heater Core Outlet Line. Removal and Installation
- Rear Heating, Ventilation and Air Conditioning (RHVAC) Control Module. Removal and Installation
- Rear Temperature Door Actuator. Removal and Installation
- Rear Temperature Sensor. Removal and Installation
- Rear Thermostatic Expansion Valve. Removal and Installation
Accelerator Pedal. Removal and Installation
Removal
NOTE:
Removal steps in this procedure may contain installation details.
NOTE:
To prevent setting Diagnostic Trouble Codes (DTCs), make
sure the ignition switch is in the OFF position prior to disconnecting
the accelerator pedal electrical connector...
Other information:
Lincoln Navigator 2018-2025 Workshop Manual: Wheels and Tires. Diagnosis and Testing
Preliminary Inspection Verify the customer concern by carrying out a road test on a smooth road. If any vibrations are apparent, Refer to the Symptom Chart: NVH. To maximize tire performance, inspect for signs of incorrect inflation and uneven wear, which may indicate a need for balancing, rotation or front suspension alignment. Correct tire pressure and d..
Lincoln Navigator 2018-2025 Workshop Manual: Engine Rear Undershield. Removal and Installation
NOTICE: Support the engine rear undershield while the fasteners are being removed and installed. Do not support the engine rear undershield by any less than the total number of fasteners at any time. Holding the shield in its correct position, remove the fasteners and the engine rear undershield. Torque: 71 lb.in (8 Nm) ..
Categories
- Manuals Home
- 4th Gen Lincoln Navigator Service Manual (2018 - 2025)
- All Terrain Control Module (ATCM). Removal and Installation
- SYNC Module [APIM]. Removal and Installation
- Body and Paint
- Power Running Board (PRB). Diagnosis and Testing
- Front Bumper Cover. Removal and Installation
Wheel to Hub Runout Minimization. General Procedures
Check
NOTE: Wheel-to-hub optimization is important. Clearance between the wheel and hub can be used to offset or neutralize the Road Force® or run-out of the wheel and tire assembly. For every 0.001 inch of wheel-to-hub clearance, the Road Force® can be affected between 1 and 3 pounds depending on the tire stiffness.
NOTE: The example below illustrates how the clearance between the wheel and the hub can be used to offset the high spot of radial run-out or Road Force®. Following the procedure will make sure of the best optimization.
Position the wheel and tire assembly on the vehicle so that the high spot location of radial run-out or Road Force® is at the 6 o'clock position and