Lincoln Navigator: Engine / Electronic Engine Controls - 3.5L EcoBoost (272kW/370PS)
- Specifications
- Electronic Engine Controls - Component Location. Description and Operation
- Electronic Engine Controls - Overview. Description and Operation
- Electronic Engine Controls - System Operation and Component Description. Description and Operation
- Crankshaft Position System. Diagnosis and Testing
- Electronic Engine Controls. Diagnosis and Testing
- Engine Starting Control System. Diagnosis and Testing
- Powertrain Control Module (PCM) Input and Output Controls. Diagnosis and Testing
- Variable Camshaft Timing (VCT) System. Diagnosis and Testing
- Camshaft Position (CMP) Sensor. Removal and Installation
- Catalyst Monitor Sensor. Removal and Installation
- Crankshaft Position (CKP) Sensor. Removal and Installation
- Cylinder Head Temperature (CHT) Sensor. Removal and Installation
- Engine Oil Pressure (EOP) Sensor. Removal and Installation
- Fuel Rail Pressure (FRP) Sensor. Removal and Installation
- Fuel Rail Pressure and Temperature Sensor. Removal and Installation
- Heated Oxygen Sensor (HO2S). Removal and Installation
- Intake Air Temperature (IAT) Sensor. Removal and Installation
- Knock Sensor (KS). Removal and Installation
- Manifold Absolute Pressure and Temperature (MAPT) Sensor. Removal and Installation
- Oil Pressure Control Solenoid. Removal and Installation
- Powertrain Control Module (PCM). Removal and Installation
- Turbocharger Boost Pressure (TCBP) and Charger Air Cooler Temperature (CACT) Sensor. Removal and Installation
- Turbocharger Bypass Valve. Removal and Installation
- Variable Camshaft Timing (VCT) Oil Control Solenoid. Removal and Installation
Fuel Tank Pressure Sensor and Tube. Removal and Installation
Removal
NOTE:
Removal steps in this procedure may contain installation details.
Remove the fuel tank.
Refer to: Fuel Tank (310-01 Fuel Tank and Lines - 3...
Specifications
Reference Value Symptom Chart
NOTE:
The Reference Value Symptom Chart provides guidance in
selecting the appropriate parameter identification (PID) or measured
signal related to the fault area...
Other information:
Lincoln Navigator 2018-2026 Workshop Manual: Anti-Lock Brake System (ABS) and Stability Control. Diagnosis and Testing
Diagnostic Trouble Code (DTC) Chart Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation). Module DTC Description Action ABS B10DA:51 PATS Target Identifier: Not Programmed GO to Pinpoint Test P ABS C0030:07 Left Fr..
Lincoln Navigator 2018-2026 Workshop Manual: Ring Gear Backlash Adjustment - Vehicles With: Electronic Limited-Slip Differential. General Procedures
Special Tool(s) / General Equipment 205-220Installer, Differential ShimTKIT-1985-FH 307-003 (T57L-500-B) Holding Fixture, Transmission Dial Indicator Copper Hammer Adjustment Remove the rear axle assembly. Refer to: Axle Assembly (205-02 Rear Drive Axle/Differential - Vehicles With: Ford 9.75 Inch Ring Gear, Removal and Install..
Categories
- Manuals Home
- 4th Gen Lincoln Navigator Service Manual (2018 - 2026)
- Rear View Mirrors - System Operation and Component Description. Description and Operation
- Windshield Washer Pump. Removal and Installation
- Body and Paint
- Transmission Fluid Level Check. General Procedures
- SYNC Module [APIM]. Removal and Installation
Rear Stabilizer Bar Link. Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details.
With the vehicle in NEUTRAL, position it on a hoist.Refer to: Jacking and Lifting (100-02 Jacking and Lifting, Description and Operation).
NOTE: Use the hex-holding feature to prevent the stud from turning while removing the nut.
Remove and discard the 2 rear stabilizer bar link nuts and remove the rear stabilizer bar link.Torque: 46 lb.ft (63 Nm)
