Lincoln Navigator: Front Suspension - LHD 4WD / Lower Ball Joint. Removal and Installation
Special Tool(s) / General Equipment
 |
204-358 Remover/Installer, Ball Joint TKIT-2005P-F TKIT-2005P-ROW |
 |
205-086
(T74P-4635-C)
Installer/Remover, C-Frame and Screw |
Removal
-
Remove the wheel knuckle.
Refer to: Wheel Knuckle (204-01B Front Suspension - LHD 4WD, Removal and Installation).
-
Remove and discard the lower ball joint snap ring.
 |
-
Remove the ball joint from the lower arm.
Use Special Service Tool: 204-358 Remover/Installer, Ball Joint. , 205-086 (T74P-4635-C) Installer/Remover, C-Frame and Screw.
 |
Installation
-
Install the ball joint into the lower arm.
Use Special Service Tool: 204-358 Remover/Installer, Ball Joint. , 205-086 (T74P-4635-C) Installer/Remover, C-Frame and Screw.
 |
-
NOTE: Make sure the ball joint snap ring is fully seated.
Install the new lower ball joint snap ring.
 |
-
Install the wheel knuckle.
Refer to: Wheel Knuckle (204-01B Front Suspension - LHD 4WD, Removal and Installation).
Lower Arm. Removal and Installation
Special Tool(s) /
General Equipment
204-592Separator, Lower Arm Ball JointTKIT-2006C-FFMFLMTKIT-2006C-LMTKIT-2006C-ROW
Removal
NOTICE:
Suspension fasteners are critical parts that affect the
performance of vital components and systems...
Shock Absorber and Spring Assembly. Removal and Installation
Special Tool(s) /
General Equipment
204-592Separator, Lower Arm Ball JointTKIT-2006C-FFMFLMTKIT-2006C-LMTKIT-2006C-ROW
Spring Compressor
Tie Rod End Remover
Removal
NOTICE:
Suspension fasteners are critical parts that affect the
performance of vital components and systems...
Other information:
Lincoln Navigator 2018-2026 Workshop Manual: Front Drive Axle and Differential. Description and Operation
The front drive axle consists of: A cast-aluminum center section, a removable cast-aluminum axle housing tube and a differential housing cover. Both the axle housing tube and the differential housing cover use silicone sealant as a gasket...
Lincoln Navigator 2018-2026 Workshop Manual: Rocker Arm. Removal and Installation
Special Tool(s) / General Equipment 303-1633Remover, Roller Rocker FollowerTKIT-2014D-ROW3TKIT-2014D-FL_ROW 303-1633-01Remover, Roller Rocker Follower Removal NOTE: This procedure should be used when removing and replacing the clipped roller finger follower or hydraulic lash adjuster and the camshafts are not removed...
Categories
- Manuals Home
- 4th Gen Lincoln Navigator Service Manual (2018 - 2026)
- Identification Codes. Description and Operation
- Body and Paint
- Head Up Display (HUD) Module Calibration. General Procedures
- Rear View Mirrors - System Operation and Component Description. Description and Operation
- Remote Function Actuator (RFA) Module. Removal and Installation
Rear Stabilizer Bar Link. Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details.
With the vehicle in NEUTRAL, position it on a hoist.Refer to: Jacking and Lifting (100-02 Jacking and Lifting, Description and Operation).
NOTE: Use the hex-holding feature to prevent the stud from turning while removing the nut.
Remove and discard the 2 rear stabilizer bar link nuts and remove the rear stabilizer bar link.Torque: 46 lb.ft (63 Nm)
