Lincoln Navigator: Wipers and Washers / Wiper Linkage Assembly. Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details.
NOTE: The hood is removed in this procedure for clarity.
-
Remove the cowl panel grill.
Refer to: Cowl Panel Grille (501-02 Front End Body Panels, Removal and Installation).
-
-
Disconnect the windshield wiper motor electrical connector.
-
If equipped, detach the windshield electrical connector retainer.
-
Disconnect the windshield wiper motor electrical connector.
 |
-
Remove the wiper linkage assembly bolts.
 |
-
Remove the wiper linkage and motor assembly.
 |
-
NOTICE: Be careful not to damage the link seals during removal. Failure to follow this instruction may result in poor windshield wiper performance.
Detach the RH windshield wiper link from the windshield wiper motor crank.
-
Detach the link.
-
Position the link aside.
-
Detach the link.
 |
-
NOTICE: Be careful not to damage the link seals during removal. Failure to follow this instruction may result in poor windshield wiper performance.
Detach the LH windshield wiper link from the windshield wiper motor crank.
-
Detach the link.
-
Position the link aside.
-
Detach the link.
 |
-
-
Position the wiper motor cover to access the linkage bolts.
-
Remove the windshield wiper motor bolts, the motor clamp plates and the wiper linkage.
Torque: 89 lb.in (10 Nm)
-
Position the wiper motor cover to access the linkage bolts.
 |
Installation
-
To install, reverse the removal procedure.
-
Tighten the wiper linkage and motor assembly bolts in the order shown.
Torque: 71 lb.in (8 Nm)
 |
Windshield Wiper Pivot Arm. Removal and Installation
Removal
NOTE:
Removal steps in this procedure may contain installation details.
Raise the windshield wiper pivot arms into the SERVICE-UP position...
Other information:
Lincoln Navigator 2018-2026 Workshop Manual: Lane Keeping System - Overview. Description and Operation
Overview The lane keeping system has 3 operating modes to help the driver stay within their lane, lane keeping aid, lane keeping alert and a combination of both the lane keeping aid and lane keeping alert. The lane keeping system modes can be selected using the touchscreen panel. The lane keeping system utilizes the IPMA camera, located on windshield (above the interior rear view mir..
Lincoln Navigator 2018-2026 Workshop Manual: Front Bumper Cover. Removal and Installation
Removal NOTE: Removal steps in this procedure may contain installation details. Remove the front wheels and tires. Refer to: Wheel and Tire (204-04A Wheels and Tires, Removal and Installation). Remove the front bumper cover lower trim pins. On both sides. Remove the fender liner screws. Torque: 15..
Categories
- Manuals Home
- 4th Gen Lincoln Navigator Service Manual (2018 - 2026)
- Vehicle Dynamics Control Module (VDM). Removal and Installation
- Windshield Washer Pump. Removal and Installation
- Brake Service Mode Activation and Deactivation. General Procedures
- Telematics Control Unit (TCU) Module. Removal and Installation
- Transmission Fluid Level Check. General Procedures
Front Stabilizer Bar Link. Removal and Installation
Removal
NOTICE: Suspension fasteners are critical parts that affect the performance of vital components and systems. Failure of these fasteners may result in major service expense. Use the same or equivalent parts if replacement is necessary. Do not use a replacement part of lesser quality or substitute design. Tighten fasteners as specified.
NOTE: Removal steps in this procedure may contain installation details.
With the vehicle in NEUTRAL, position it on a hoist.Refer to: Jacking and Lifting (100-02 Jacking and Lifting, Description and Operation).
NOTICE: Do not use power tools to remove or install the stabilizer bar
