Lincoln Navigator Manuals

Lincoln Navigator: Automatic Transmission - 10-Speed Automatic Transmission – 10R80 / C Clutch. Diagnosis and Testing

Lincoln Navigator 2018-2026 Workshop Manual / Automatic Transmission / Automatic Transmission - 10-Speed Automatic Transmission – 10R80 / C Clutch. Diagnosis and Testing

Symptom Chart

C Clutch

For C clutch operation,
REFER to: C Clutch (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Description and Operation).


  C Clutch


Condition Possible Sources Action
C clutch does not apply SSC mechanically stuck OFF INSTALL a new solenoid.
REFER to: Shift Solenoids (SS) (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
C clutch control valve stuck OFF DISASSEMBLE, CLEAN and INSPECT the C clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
C clutch latch valve stuck OFF DISASSEMBLE, CLEAN and INSPECT the C clutch latch valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
C clutch hydraulic circuit blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris, blockage and leaks. CLEAN as necessary.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
CARRY OUT the air pressure test on the C clutch.
REFER to: Special Testing Procedures (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Diagnosis and Testing).
If a leak is detected, INSPECT the front support assembly, input shaft Teflon seals, CDF clutch cylinder and C clutch piston seals for leaks. INSTALL new components as necessary. REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
CDF clutch cylinder, ring gear no. 2, sun gear no. 3 DISASSEMBLE and INSPECT the CDF clutch cylinder, ring gear no. 2 and sun gear no. 3 for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
C clutch piston seals DISASSEMBLE and INSPECT the C clutch piston seals for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
C clutch friction plates DISASSEMBLE and INSPECT the C clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
C clutch always applied SSC mechanically stuck ON INSTALL a new solenoid.
REFER to: Shift Solenoids (SS) (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
C clutch control valve stuck ON DISASSEMBLE, CLEAN and INSPECT the C clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
C clutch latch valve stuck ON DISASSEMBLE, CLEAN and INSPECT the C clutch latch valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
C clutch hydraulic circuit cross leaks DISASSEMBLE and INSPECT the main control valve body and separator plate passages for cracks, warping and damage. If damage is found, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
CDF clutch cylinder, ring gear no. 2 DISASSEMBLE and INSPECT the components for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
C clutch piston return spring DISASSEMBLE and INSPECT the C clutch piston return spring for damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
C clutch friction plates DISASSEMBLE and INSPECT the C clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
C clutch delayed/soft/slipping apply Incorrect transmission strategy programmed into PCM / TCM . CARRY OUT the Transmission Strategy Download and the Adaptive Learning Drive Cycle.
REFER to: Transmission Strategy Download (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, General Procedures).
REFER to: Adaptive Learning Drive Cycle (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, General Procedures).
Low line pressure CARRY OUT the line pressure test. If line pressure is low, REFER to the Line Pressure Diagnosis Chart.
REFER to: Special Testing Procedures (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Diagnosis and Testing).
SSC mechanically sticking INSTALL a new solenoid.
REFER to: Shift Solenoids (SS) (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
C clutch control valve sticking DISASSEMBLE, CLEAN and INSPECT the C clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
C clutch latch valve sticking DISASSEMBLE, CLEAN and INSPECT the C clutch latch valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
C clutch hydraulic circuits blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris, blockage and leaks. CLEAN as necessary.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
CARRY OUT the air pressure test on the C clutch.
REFER to: Special Testing Procedures (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Diagnosis and Testing).
If a leak is detected, INSPECT the front support assembly, input shaft Teflon seals, CDF clutch cylinder and C clutch piston seals for leaks. INSTALL new components as necessary. REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
C clutch piston seals DISASSEMBLE and INSPECT the C clutch piston seals for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
C clutch friction plates DISASSEMBLE and INSPECT the C clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
C clutch harsh apply Incorrect transmission strategy programmed into PCM / TCM . CARRY OUT the Transmission Strategy Download and the Adaptive Learning Drive Cycle.
REFER to: Transmission Strategy Download (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, General Procedures).
REFER to: Adaptive Learning Drive Cycle (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, General Procedures).
High line pressure CARRY OUT the line pressure test. If line pressure is high, REFER to the Line Pressure Diagnosis Chart.
REFER to: Special Testing Procedures (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Diagnosis and Testing).
SSC mechanically sticking INSTALL a new solenoid.
REFER to: Shift Solenoids (SS) (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
C clutch control valve sticking DISASSEMBLE, CLEAN and INSPECT the C clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
C clutch latch valve sticking DISASSEMBLE, CLEAN and INSPECT the C clutch latch valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
C clutch hydraulic circuit blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris, blockage and leaks. CLEAN as necessary.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
C clutch piston return spring DISASSEMBLE and INSPECT the C clutch piston return spring for damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
C clutch friction plates DISASSEMBLE and INSPECT the C clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).

    B Clutch. Diagnosis and Testing

    Symptom Chart B Clutch For B clutch operation, REFER to: B Clutch (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Description and Operation)...

    D Clutch. Diagnosis and Testing

    Symptom Chart D Clutch For D clutch operation, REFER to: D Clutch (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Description and Operation)...

    Other information:

    Lincoln Navigator 2018-2026 Workshop Manual: Engine. Disassembly


    Special Tool(s) / General Equipment 205-142 (T80T-4000-J) Installer, Differential Bearing Cone 205-150 (T80T-4000-S) Installer, Spindle Bearing 205-153 (T80T-4000-W) Handle 303-1246Engine Spreader BarTKIT-2006UF-FLMTKIT-2006UF-ROW 303-1247VCT Spark Plug Tube Seal Remover and InstallerTKIT-2006UF-FLMTKIT-2006UF-ROW 303-1..

    Lincoln Navigator 2018-2026 Workshop Manual: Climate Control Housing. Removal and Installation


    Removal NOTICE: During the removal or installation of components, cap, tape or otherwise appropriately protect all openings and tubes/fittings to prevent the ingress of dirt or other contamination. Remove caps, tape and other protective materials prior to installation. NOTE: Removal steps in this procedure may contain installation details. Recover the refrigeran..

    Categories

    Front Driveshaft. Removal and Installation

    Special Tool(s) / General Equipment

    Crimping Tool

    Materials

    Name Specification Motorcraft® Premium Long-Life Grease
    XG-1-E1 ESA-M1C75-B
     

    Removal

    With the vehicle in NEUTRAL, position the vehicle on a hoist.
    Refer to: Jacking and Lifting (100-02 Jacking and Lifting, Description and Operation).
    Remove the bolts and the transmission shield.

    read more

    Copyright © 2026 www.linavigator4.com