Lincoln Navigator Manuals

Lincoln Navigator: Automatic Transmission - 10-Speed Automatic Transmission – 10R80 / D Clutch. Diagnosis and Testing

Lincoln Navigator 2018-2025 Workshop Manual / Automatic Transmission / Automatic Transmission - 10-Speed Automatic Transmission – 10R80 / D Clutch. Diagnosis and Testing

Symptom Chart

D Clutch

For D clutch operation,
REFER to: D Clutch (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Description and Operation).


  D Clutch


Condition Possible Sources Action
D clutch does not apply SSD mechanically stuck OFF INSTALL a new solenoid.
REFER to: Shift Solenoids (SS) (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
D clutch control valve stuck OFF DISASSEMBLE, CLEAN and INSPECT the D clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
D clutch hydraulic circuits blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris, blockage and leaks. CLEAN as necessary.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
CARRY OUT the air pressure test on the D clutch.
REFER to: Special Testing Procedures (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Diagnosis and Testing).
If a leak is detected, INSPECT the front support assembly, input shaft Teflon seals and D clutch piston seals for leaks. INSTALL new components as necessary. REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
CDF clutch cylinder, planetary carrier no. 3 DISASSEMBLE and INSPECT the CDF clutch cylinder and planetary carrier no. 3 for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch piston seals DISASSEMBLE and INSPECT the D clutch piston seals for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch friction plates DISASSEMBLE and INSPECT the D clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch always applied SSD mechanically stuck ON INSTALL a new solenoid.
REFER to: Shift Solenoids (SS) (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
D clutch control valve stuck ON DISASSEMBLE, CLEAN and INSPECT the D clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
D clutch hydraulic circuit cross leaks DISASSEMBLE and INSPECT the main control valve body and separator plate passages for cracks, warping and damage. If damage is found, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
CDF clutch cylinder, planetary carrier no. 3 DISASSEMBLE and INSPECT the components for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch piston return spring DISASSEMBLE and INSPECT the D clutch piston return spring for damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch friction plates DISASSEMBLE and INSPECT the D clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch delayed/soft/slipping apply Incorrect transmission strategy programmed into PCM / TCM . CARRY OUT the Transmission Strategy Download and the Adaptive Learning Drive Cycle.
REFER to: Transmission Strategy Download (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, General Procedures).
REFER to: Adaptive Learning Drive Cycle (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, General Procedures).
Low line pressure CARRY OUT the line pressure test. If line pressure is low, REFER to the Line Pressure Diagnosis Chart.
REFER to: Special Testing Procedures (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Diagnosis and Testing).
SSD mechanically sticking INSTALL a new solenoid.
REFER to: Shift Solenoids (SS) (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
D clutch control valve sticking DISASSEMBLE, CLEAN and INSPECT the D clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
Gain control valve stuck in default position. DISASSEMBLE, CLEAN and INSPECT the clutch gain control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
D clutch hydraulic circuits blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris, blockage and leaks. CLEAN as necessary.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
CARRY OUT the air pressure test on the D clutch.
REFER to: Special Testing Procedures (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Diagnosis and Testing).
If a leak is detected, INSPECT the front support assembly, input shaft Teflon seals and D clutch piston seals for leaks. INSTALL new components as necessary. REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch piston seals DISASSEMBLE and INSPECT the D clutch piston seals for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch friction plates DISASSEMBLE and INSPECT the D clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch harsh apply Incorrect transmission strategy programmed into PCM / TCM . CARRY OUT the Transmission Strategy Download and the Adaptive Learning Drive Cycle.
REFER to: Transmission Strategy Download (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, General Procedures).
REFER to: Adaptive Learning Drive Cycle (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, General Procedures).
High line pressure CARRY OUT the line pressure test. If line pressure is high, REFER to the Line Pressure Diagnosis Chart.
REFER to: Special Testing Procedures (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Diagnosis and Testing).
SSD mechanically sticking INSTALL a new solenoid.
REFER to: Shift Solenoids (SS) (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
D clutch control valve sticking DISASSEMBLE, CLEAN and INSPECT the D clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
Gain control valve stuck in applied position DISASSEMBLE, CLEAN and INSPECT the clutch gain control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
D clutch hydraulic circuits blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris, blockage and leaks. CLEAN as necessary.
REFER to: Main Control Valve Body (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
D clutch piston return spring DISASSEMBLE and INSPECT the D clutch piston return spring for damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch friction plates DISASSEMBLE and INSPECT the D clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).

    C Clutch. Diagnosis and Testing

    Symptom Chart C Clutch For C clutch operation, REFER to: C Clutch (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Description and Operation)...

    E Clutch. Diagnosis and Testing

    Symptom Chart E Clutch For E clutch operation, REFER to: E Clutch (307-01 Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Description and Operation)...

    Other information:

    Lincoln Navigator 2018-2025 Workshop Manual: Wipers and Washers - Overview. Description and Operation


    Overview The windshield wiper/washer system is activated by the wiper/washer switch. The following functions/ features of the windshield wiper/washer system are: Mist wipe Windshield wash (includes front camera wash, if equipped) Courtesy wipe Windshield wipers (low/high speed) Intermittent wipers Speed dependent wipers Wiper activate..

    Lincoln Navigator 2018-2025 Workshop Manual: Transfer Case Rear Seal. Removal and Installation


    Special Tool(s) / General Equipment 308-249 (T96T-7127-A) Installer, Input Shaft Oil SealTKIT-1996-F/FMTKIT-1996-FLM2 Removal With the vehicle in NEUTRAL, position it on a hoist. Refer to: Jacking and Lifting (100-02 Jacking and Lifting, Description and Operation). Remove the rear driveshaft. Refer to: Rear Driveshaft (205-01 Drives..

    Categories

    Rear Drive Halfshafts. Diagnosis and Testing

    Preliminary Inspection

    Visually inspect the CV joints, housing, boots, and clamps for obvious signs of mechanical damage.
    If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step
    If the cause is not visually evident, verify the symptom and REFER to Symptom Chart: NVH.

    read more

    Copyright © 2025 www.linavigator4.com