• Navigator Manuals
  • Service
  • New
  • Top
  • Sitemap
Lincoln Navigator Manuals

Lincoln Navigator: Starting System - 3.5L EcoBoost (272kW/370PS) / Starting System - Overview. Description and Operation

Lincoln Navigator 2018-2026 Workshop Manual / Engine / Starting System - 3.5L EcoBoost (272kW/370PS) / Starting System - Overview. Description and Operation

Starting System

The starting system controls the cranking of the engine. The PCM energizes the starter relay when it receives inputs from the ignition switch, automatic transmission, and the BCM . When the starter relay is energized it applies power to the starter motor which cranks the engine.

Starting System - with Remote Start

If equipped, the remote start system allows the vehicle to be started from up to 20 meters (65 feet) away. For more information on the remote start system, refer to the owners literature and
Refer to: Handles, Locks, Latches and Entry Systems - System Operation and Component Description (501-14 Handles, Locks, Latches and Entry Systems, Description and Operation).

Starting System - with Auto-Start-Stop

The Auto-Start-Stop system helps reduce fuel consumption by automatically shutting off the vehicle’s engine while the vehicle is at a complete stop and restarting the engine when the brake pedal is released. The Auto-Start-Stop system is automatically enabled whenever the ignition is turned on. The vehicle may restart automatically in order to maintain interior comfort or to recharge the battery.

Refer to the Owner's Literature for additional information.

    Specifications

      General Specifications Item Specification Normal engine cranking speed (Average) 240-300 RPM Starting circuit maximum voltage drop (Engine at normal operating temperature) (Average) 1...

    Starting System - System Operation and Component Description. Description and Operation

    System Operation System Diagram *.sttxt { visibility: hidden; } *.stcallout { visibility: visible; } E342312 1 Ignition Switch 2 BCM 3..

    Other information:

    Lincoln Navigator 2018-2026 Workshop Manual: Lower Ball Joint. Removal and Installation


    Special Tool(s) / General Equipment 204-358Remover/Installer, Ball JointTKIT-2005P-FTKIT-2005P-ROW 205-086 (T74P-4635-C) Installer/Remover, C-Frame and Screw Removal Remove the wheel knuckle. Refer to: Wheel Knuckle (204-01B Front Suspension - LHD 4WD, Removal and Installation). Remove and discard the lower ball joint sn..

    Lincoln Navigator 2018-2026 Workshop Manual: Parking Aid - System Operation and Component Description. Description and Operation


    System Operation Overview - Active Park Assist NOTE: Vehicles equipped with active park assist use a different parking aid sensor. The IPMA supplies a 12v reference voltage and a ground. The signal circuit is a LIN used to comunicate the sensor data with the IPMA . The active park assist system is a supplementary parking system that assists the operator with the task of pa..

    Categories

    • Manuals Home
    • 4th Gen Lincoln Navigator Service Manual (2018 - 2026)
    • Identification Codes. Description and Operation
    • Remote Function Actuator (RFA) Module. Removal and Installation
    • Body Control Module (BCM). Removal and Installation
    • Vehicle Dynamics Control Module (VDM). Removal and Installation
    • Brake Service Mode Activation and Deactivation. General Procedures

    Rear Stabilizer Bar Link. Removal and Installation

    Removal

    NOTE: Removal steps in this procedure may contain installation details.

    With the vehicle in NEUTRAL, position it on a hoist.
    Refer to: Jacking and Lifting (100-02 Jacking and Lifting, Description and Operation).

    NOTE: Use the hex-holding feature to prevent the stud from turning while removing the nut.

    Remove and discard the 2 rear stabilizer bar link nuts and remove the rear stabilizer bar link.
    Torque: 46 lb.ft (63 Nm)

    read more

    Copyright © 2026 www.linavigator4.com