Lincoln Navigator: Engine Cooling - 3.5L EcoBoost (272kW/370PS) / Engine Cooling - Component Location. Description and Operation
NOTE: Coolant temperature will vary with ambient temperature and load. Temperatures shown are for ambient temperature of 38° C (100° F). Red arrows indicate a temperature over 90° C (194° F), Orange arrows indicate a temperature of approximately 90° C (194° F), Blue arrows indicate a temperature below 90° C (194° F).
| Item | Description |
|---|---|
| 1 | Radiator |
| 2 | Lower radiator hose and clamp assembly |
| 3 | Oil cooler |
| 4 | Coolant pump-to-transmission fluid cooler hose |
| 5 | Transmission fluid heater coolant control valve outlet hose |
| 6 | Radiator-to-degas bottle hose |
| 7 | Heater hose assembly |
| 8 | Pressure relief cap |
| 9 | Degas bottle |
| 10 | Upper radiator hose and clamp assembly |
| 11 | Thermostat housing |
| 12 | Coolant outlet connector |
| 13 | Coolant pump |
| 14 | Engine front cover |
| 15 | Cabin Heater Coolant Pump |
| 16 | Thermostat housing-to-degas bottle hose |
| 17 | Turbocharger RH |
| 18 | Turbocharger inlet tube RH |
| 19 | Turbocharger outlet tube RH |
| 20 | Cylinder head RH |
| 21 | Cylinder block coolant pump hole cover |
| 22 | Cylinder block |
| 23 | Transmission fluid cooler inlet tube |
| 24 | Transmission fluid cooler |
| 25 | Turbocharger inlet tube LH |
| 26 | Turbocharger LH |
| 27 | Turbocharger outlet tube LH |
| 28 | Cylinder head LH |
| 29 | Auxiliary Heater core |
| 30 | Heater core |
Specifications
Coolant Capacity: Vehicles Built Up To: 08-July-2018
Name
Fill Capacity
Material: Motorcraft® Orange Concentrated Antifreeze/Coolant
/ VC-3-B
(WSS-M97B44-D)
Base radiator — 18...
Engine Cooling - System Operation and Component Description. Description and Operation
System Operation
Engine coolant flows primarily from the engine to the radiator circuit
and back to the coolant pump. Coolant is sent from the coolant pump
through the engine block and cylinder heads...
Other information:
Lincoln Navigator 2018-2026 Workshop Manual: Engine Rear Undershield. Removal and Installation
NOTICE: Support the engine rear undershield while the fasteners are being removed and installed. Do not support the engine rear undershield by any less than the total number of fasteners at any time. Holding the shield in its correct position, remove the fasteners and the engine rear undershield...
Lincoln Navigator 2018-2026 Workshop Manual: Cooling Module. Removal and Installation
Special Tool(s) / General Equipment Hose Clamp Remover/Installer Removal NOTE: Removal steps in this procedure may contain installation details. With the vehicle in NEUTRAL, position it on a hoist. Refer to: Jacking and Lifting (100-02 Jacking and Lifting, Description and Operation)...
Categories
- Manuals Home
- 4th Gen Lincoln Navigator Service Manual (2018 - 2026)
- SYNC Module [APIM]. Removal and Installation
- Identification Codes. Description and Operation
- Front Seat. Removal and Installation
- Front Bumper Cover. Removal and Installation
- Second Row Seat. Removal and Installation
Front Driveshaft. Removal and Installation
Special Tool(s) / General Equipment
Crimping ToolMaterials
Name Specification Motorcraft® Premium Long-Life GreaseXG-1-E1 ESA-M1C75-B
Removal
With the vehicle in NEUTRAL, position the vehicle on a hoist.Refer to: Jacking and Lifting (100-02 Jacking and Lifting, Description and Operation).
Remove the bolts and the transmission shield.
